Tuotetta on etävarastossamme, toimitusaika noin 5-6 työpäivää. Lisätietoja
Kuljetuksen hinta 150,60 Kuormalavatoimitus katutasolle (arkisin 8:00-16:00) – Takaraja klo 15.00 toimituksen lähtöön samana päivänä
Toimituskulut on laskettu vastaanottajan postinumeron perusteella: - Vaihda postinumero
Syötä postinumero toimitusta varten: Tallenna
EUR
153,71
ilman ALV 122,48
Kokonaishinta sis. toimitus
304,31
Tämä toiminto vaatii sisäänkirjautumisen. Luo käyttäjä ja voit käyttää listojamme esim. säännöllisiä ostoksia ja toivelistoja varten Luo käyttäjä Kirjaudu
PowerBoost is the perfect power supply for your power-hungry portable project! This little DC/DC boost converter module can run from 1.8V batteries or higher, and convert that voltage to 5.2V DC for running your 5V projects. With a beefy 4A DC/DC converter, it can give you 1A+ from as low as 2V.
Like our popular 5V 1A USB wall adapter, we tweaked the output to be 5.2V instead of a straight-up 5.0V so that there's a little bit of 'headroom' long cables, high draw, the addition of a diode on the output if you wish, etc. The 5.2V is safe for all 5V-powered electronics like Arduino, Raspberry Pi, or Beagle Bone while preventing icky brown-outs during high current draw because of USB cable resistance.
The PowerBoost 1000 has at the heart a TPS61030 boost converter from TI. This boost converter chip has some really nice extras such as low battery detection, 4A internal switch, synchronous conversion, excellent efficiency, and 700KHz high-frequency operation. Check out these specs!
- Synchronous operation means you can disconnect the output completely by connecting the ENable pin to ground. This will completely turn off the output - 4A internal switch means you can get 1000mA+ from as low as 1.8V, 1500mA+ from 2 NiMH or Alkaline batteries, and at least 2000mA from a 3.7V LiPoly/LiIon battery or 3 NiMH/Alkalines. Just make sure your batteries can actually supply the required 2-4A, OK? - Low battery indicator LED lights up red when the voltage dips below 3.2V, optimized for the most common usage of LiPo/LiIon battery usage - On-board 1000mA charge-rate 'Apple/iOS' data resistors. Solder in the included USB connector and you can plug in any iPhone or iPod for a speedy 1000mA charge rate. Works with iPads, both mini and 'classic' type. - Full breakout for battery in, control pins and power out - 90%+ operating efficiency in most cases (see datasheet for efficiency graphs), and low quiescent current: 5mA when enabled and power LED is on, 20uA when disabled (power and low batt LED are off)
Great for powering your robot, Arduino project, single-board-computer such as Raspberry Pi or BeagleBone! Each order comes with one fully assembled and tested PCB, a loose 2-PH JST jack, a 2-pin Terminal block and a loose USB A jack.
If you are powering your project from USB, solder the USB A jack in (a 3-minute soldering task). Then choose either JST for input (JST is often used for our LiIon batteries, but the connector is only rated for 2A) or a terminal block.
The 1000 version comes with a 2-pin terminal block so you can solder it to the output spot where the USB jack would go. Or don't solder any connectors in for a more compact power pack and go with 22AWG wires soldered directly in.
Tuotetyyppi
Tehomoduuli
Yhteensopivuus
Arduino/Beagle Bone/Raspberry Pi
Tuotemerkin yhteensopivuus
Adafruit
Signaalinlähtö
5,2 V
Kestävän kehityksen sertifikaatit
RoHS
Tuotteen leveys
29 mm
Tuotteen syvyys
23 mm
Tuotteen korkeus
2 mm
Paino
6 g
Löydämme tuotteen järjestelmästämme helposti seuraavalla tuotenumerolla
EAN:
2050004690583
SKU:
ADA-2030
Varför upplever jag att exakt samma varor finns med flera olika produktnummer?
Tillverkarna ger ofta ut samma produkter med olika produktnummer, vanligtvis handlar det uteslutet om olika versioner av emballage. T.ex. så kan emballaget målinriktas för olika länder.
Vi försöker på bästa sätt samla varorna, men det kan upplevas som att samma produkter finns med olika produktnummer i vårt system.